{"title":"Threaded Rod","description":"\u003cp\u003e1m (1000mm) fully threaded rod and studding to DIN 976 in A2 stainless steel (M2-M24) or zinc plated steel (M4-M30). Packs of 1 to 5.\u003c\/p\u003e","products":[{"product_id":"1m-fully-threaded-rod-a2-304-stainless-steel-din-976","title":"1m Fully Threaded Rod A2 Stainless Steel DIN 976 Stud Bolt","description":"\u003cp\u003e\u003cstrong\u003eA2 stainless steel threaded rod made to DIN 976\u003c\/strong\u003e, fully threaded along its entire 1 metre length with a standard right-hand ISO metric thread. Because the thread runs continuously from end to end rather than being confined to short lengths at each tip, a nut can be started and run down from either end, or fixed and locked at any point along the rod - making it a genuinely flexible stud\/studding bar rather than a fixed-length stud bolt.\u003c\/p\u003e\n\u003cp\u003eIt's available across a wide size range, from the fine M2 thread used in small instrument, electronics and precision assembly work, right up to the heavy M24 thread used for structural and load-bearing connections - so whichever end of that range a job calls for, the same fully-threaded, cut-to-length format applies.\u003c\/p\u003e\n\u003cp\u003eDIN 976 is the modern, tighter-tolerance successor to the older DIN 975 threaded rod standard, and the two designations are still commonly quoted together in the trade for this type of product, so it may also be listed elsewhere as DIN 975\/976 studding. Manufactured in A2 austenitic stainless steel, it combines good general corrosion resistance with the strength needed for structural tie rods, suspended fixings and general fabrication work, without the surface rust that a plain or zinc-plated rod would eventually show.\u003c\/p\u003e\n\u003cp\u003eBecause it is supplied fully threaded rather than threaded at each end only, the rod can be cut down to any shorter length on site with a hacksaw or angle grinder and will still take a nut cleanly anywhere along the cut length - there's no need to work around a fixed unthreaded section in the middle, and no offcut is wasted thread.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eKey Features\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eA2 stainless steel construction resists surface rust and corrosion far better than plain or zinc-plated steel rod\u003c\/li\u003e\n\u003cli\u003eManufactured to DIN 976, the modern, tighter-tolerance successor to the DIN 975 threaded rod standard\u003c\/li\u003e\n\u003cli\u003eFully threaded along the entire 1 metre length, so a nut can be started and run down from either end\u003c\/li\u003e\n\u003cli\u003eStandard right-hand ISO metric thread, compatible with ordinary metric nuts, washers and coupling nuts\u003c\/li\u003e\n\u003cli\u003eCan be cut to any shorter length on site with a hacksaw or angle grinder and will still take a nut anywhere along the cut\u003c\/li\u003e\n\u003cli\u003eSupplied as a single 1m length rather than a fixed-length stud bolt, giving full control over the finished length\u003c\/li\u003e\n\u003cli\u003eSpans a full size range from M2 up to M24, each with its correct ISO metric thread pitch, covering everything from light precision work to heavy structural connections\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eSpecification\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eMaterial: A2 stainless steel\u003c\/li\u003e\n\u003cli\u003eStandard: DIN 976\u003c\/li\u003e\n\u003cli\u003eLength: 1m, fully threaded\u003c\/li\u003e\n\u003cli\u003eThread: Right-hand, ISO metric, fully threaded along the entire length\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eFull size range and thread pitch:\u003c\/strong\u003e\u003c\/p\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth\u003eSize\u003c\/th\u003e\n\u003cth\u003eThread Pitch (mm)\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eM2\u003c\/td\u003e\n\u003ctd\u003e0.4\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eM3\u003c\/td\u003e\n\u003ctd\u003e0.5\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eM5\u003c\/td\u003e\n\u003ctd\u003e0.8\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eM6\u003c\/td\u003e\n\u003ctd\u003e1.0\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eM8\u003c\/td\u003e\n\u003ctd\u003e1.25\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eM10\u003c\/td\u003e\n\u003ctd\u003e1.5\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eM12\u003c\/td\u003e\n\u003ctd\u003e1.75\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eM16\u003c\/td\u003e\n\u003ctd\u003e2.0\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eM18\u003c\/td\u003e\n\u003ctd\u003e2.5\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eM20\u003c\/td\u003e\n\u003ctd\u003e2.5\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eM22\u003c\/td\u003e\n\u003ctd\u003e2.5\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eM24\u003c\/td\u003e\n\u003ctd\u003e3.0\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003e\u003cstrong\u003eTypical Applications\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eConstruction and architectural framework - tie rods, hanger rods and general structural fixing where a stainless finish is specified\u003c\/li\u003e\n\u003cli\u003eIndustrial machinery manufacturing - mounting studs, frame tie rods and equipment bases\u003c\/li\u003e\n\u003cli\u003eAutomotive assembly - general fixing and mounting work during vehicle build and fit-out\u003c\/li\u003e\n\u003cli\u003eGeneral DIY and home repair - anywhere a length of threaded bar needs to be cut to size and used with standard metric nuts\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eInstallation Guidance\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eCut the rod to the length you need with a hacksaw or angle grinder, then deburr the cut end with a file so a nut runs on cleanly rather than snagging on a raised edge. A useful trade tip when cutting threaded rod: run a nut up past the cutting point before you cut, then wind it back off once the cut is made - this re-forms any thread that gets slightly deformed by the cutting action, so a fresh nut starts easily on the newly cut end.\u003c\/p\u003e\n\u003cp\u003eBecause this rod is fully threaded rather than threaded only at each end, it can be positioned and fixed at any point along its length rather than only at the tips - useful where the fixing point needs to sit mid-span rather than at an end. Where a rod needs to be joined to another length, use a coupling nut matched to the M-size in use, and where vibration is likely, a second nut run up and locked against the first (a jam nut) will help stop the fixing working loose over time. To keep the full benefit of the stainless finish, pair the rod with A2 stainless nuts and washers rather than plain or zinc-plated ones - mixing stainless fasteners with ordinary steel nuts can lead to the steel components corroding at the joint, and over time makes nuts harder to remove.\u003c\/p\u003e\n\u003cp\u003eOrder before 2pm Mon–Fri for same-day dispatch from our UK warehouse.\u003c\/p\u003e","brand":"DIYUK","offers":[{"title":"M2 (Pitch: 0.4) \/ Pack of: 1","offer_id":40487859585158,"sku":"ROD-DIN976-M2-1","price":12.1,"currency_code":"GBP","in_stock":false},{"title":"M2 (Pitch: 0.4) \/ Pack of: 2","offer_id":40487860076678,"sku":"ROD-DIN976-M2-2","price":15.22,"currency_code":"GBP","in_stock":false},{"title":"M2 (Pitch: 0.4) \/ Pack of: 5","offer_id":40487860109446,"sku":"ROD-DIN976-M2-5","price":21.6,"currency_code":"GBP","in_stock":false},{"title":"M3 (Pitch: 0.5) \/ Pack of: 1","offer_id":40487859617926,"sku":"ROD-DIN976-M3-1","price":11.1,"currency_code":"GBP","in_stock":false},{"title":"M3 (Pitch: 0.5) \/ Pack of: 2","offer_id":40487860142214,"sku":"ROD-DIN976-M3-2","price":12.35,"currency_code":"GBP","in_stock":false},{"title":"M3 (Pitch: 0.5) \/ Pack of: 5","offer_id":40487860174982,"sku":"ROD-DIN976-M3-5","price":17.1,"currency_code":"GBP","in_stock":false},{"title":"M5 (Pitch: 0.8) \/ Pack of: 1","offer_id":40487859650694,"sku":"ROD-DIN976-M5-1","price":10.97,"currency_code":"GBP","in_stock":false},{"title":"M5 (Pitch: 0.8) \/ Pack of: 2","offer_id":40487860207750,"sku":"ROD-DIN976-M5-2","price":11.97,"currency_code":"GBP","in_stock":false},{"title":"M5 (Pitch: 0.8) \/ Pack of: 5","offer_id":40487860240518,"sku":"ROD-DIN976-M5-5","price":15.97,"currency_code":"GBP","in_stock":false},{"title":"M6 (Pitch: 1.0) \/ Pack of: 1","offer_id":40487859683462,"sku":"ROD-DIN976-M6-1","price":11.1,"currency_code":"GBP","in_stock":true},{"title":"M6 (Pitch: 1.0) \/ Pack of: 2","offer_id":40487860273286,"sku":"ROD-DIN976-M6-2","price":12.35,"currency_code":"GBP","in_stock":true},{"title":"M6 (Pitch: 1.0) \/ Pack of: 5","offer_id":40487860306054,"sku":"ROD-DIN976-M6-5","price":17.1,"currency_code":"GBP","in_stock":false},{"title":"M8 (Pitch: 1.25) \/ Pack of: 1","offer_id":40487859716230,"sku":"ROD-DIN976-M8-1","price":11.97,"currency_code":"GBP","in_stock":false},{"title":"M8 (Pitch: 1.25) \/ Pack of: 2","offer_id":40487860338822,"sku":"ROD-DIN976-M8-2","price":14.1,"currency_code":"GBP","in_stock":false},{"title":"M8 (Pitch: 1.25) \/ Pack of: 5","offer_id":40487860371590,"sku":"ROD-DIN976-M8-5","price":21.22,"currency_code":"GBP","in_stock":false},{"title":"M10 (Pitch: 1.5) \/ Pack of: 1","offer_id":40487859748998,"sku":"ROD-DIN976-M10-1","price":13.22,"currency_code":"GBP","in_stock":false},{"title":"M10 (Pitch: 1.5) \/ Pack of: 2","offer_id":40487860404358,"sku":"ROD-DIN976-M10-2","price":17.47,"currency_code":"GBP","in_stock":false},{"title":"M10 (Pitch: 1.5) \/ Pack of: 5","offer_id":40487860437126,"sku":"ROD-DIN976-M10-5","price":27.22,"currency_code":"GBP","in_stock":false},{"title":"M12 (Pitch: 1.75) \/ Pack of: 1","offer_id":40487859781766,"sku":"ROD-DIN976-M12-1","price":15.72,"currency_code":"GBP","in_stock":false},{"title":"M12 (Pitch: 1.75) \/ Pack of: 2","offer_id":40487860469894,"sku":"ROD-DIN976-M12-2","price":20.35,"currency_code":"GBP","in_stock":false},{"title":"M12 (Pitch: 1.75) \/ Pack of: 5","offer_id":40487860502662,"sku":"ROD-DIN976-M12-5","price":34.47,"currency_code":"GBP","in_stock":false},{"title":"M16 (Pitch: 2.0) \/ Pack of: 1","offer_id":40487859814534,"sku":"ROD-DIN976-M16-1","price":19.6,"currency_code":"GBP","in_stock":false},{"title":"M16 (Pitch: 2.0) \/ Pack of: 2","offer_id":40487860535430,"sku":"ROD-DIN976-M16-2","price":28.22,"currency_code":"GBP","in_stock":false},{"title":"M16 (Pitch: 2.0) \/ Pack of: 5","offer_id":40487860568198,"sku":"ROD-DIN976-M16-5","price":53.97,"currency_code":"GBP","in_stock":false},{"title":"M18 (Pitch: 2.5) \/ Pack of: 1","offer_id":40487859847302,"sku":"ROD-DIN976-M18-1","price":22.1,"currency_code":"GBP","in_stock":false},{"title":"M18 (Pitch: 2.5) \/ Pack of: 2","offer_id":40487860600966,"sku":"ROD-DIN976-M18-2","price":33.22,"currency_code":"GBP","in_stock":false},{"title":"M18 (Pitch: 2.5) \/ Pack of: 5","offer_id":40487860633734,"sku":"ROD-DIN976-M18-5","price":66.47,"currency_code":"GBP","in_stock":false},{"title":"M20 (Pitch: 2.5) \/ Pack of: 1","offer_id":40487859880070,"sku":"ROD-DIN976-M20-1","price":24.22,"currency_code":"GBP","in_stock":false},{"title":"M20 (Pitch: 2.5) \/ Pack of: 2","offer_id":40487860666502,"sku":"ROD-DIN976-M20-2","price":37.35,"currency_code":"GBP","in_stock":false},{"title":"M20 (Pitch: 2.5) \/ Pack of: 5","offer_id":40487860699270,"sku":"ROD-DIN976-M20-5","price":77.22,"currency_code":"GBP","in_stock":false},{"title":"M22 (Pitch: 2.5) \/ Pack of: 1","offer_id":40487859912838,"sku":"ROD-DIN976-M22-1","price":28.22,"currency_code":"GBP","in_stock":false},{"title":"M22 (Pitch: 2.5) \/ Pack of: 2","offer_id":40487860732038,"sku":"ROD-DIN976-M22-2","price":45.35,"currency_code":"GBP","in_stock":false},{"title":"M22 (Pitch: 2.5) \/ Pack of: 5","offer_id":40487860764806,"sku":"ROD-DIN976-M22-5","price":97.22,"currency_code":"GBP","in_stock":false},{"title":"M24 (Pitch: 3.0) \/ Pack of: 1","offer_id":40487859945606,"sku":"ROD-DIN976-M24-1","price":30.35,"currency_code":"GBP","in_stock":false},{"title":"M24 (Pitch: 3.0) \/ Pack of: 2","offer_id":40487860797574,"sku":"ROD-DIN976-M24-2","price":49.73,"currency_code":"GBP","in_stock":false},{"title":"M24 (Pitch: 3.0) \/ Pack of: 5","offer_id":40487860830342,"sku":"ROD-DIN976-M24-5","price":115.72,"currency_code":"GBP","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0549\/0245\/6454\/files\/RODMAIN.png?v=1706475041"},{"product_id":"premium-1000mm-fully-threaded-steel-stud-bar-zinc-plated-din-976","title":"Premium 1000mm Fully Threaded Steel Studding Bar - Zinc Plated (DIN 976)","description":"\u003cp\u003e\u003cstrong\u003eZinc-plated steel threaded rod (studding bar) made to DIN 976\u003c\/strong\u003e, fully threaded along its entire 1000mm (39.4\") length with a standard right-hand ISO metric thread - meaning it tightens in the same clockwise direction as a standard nut or bolt. Because the thread runs continuously from end to end rather than stopping short at each tip, a nut can be started and run down from either end of the rod, or positioned and locked off at any point along its length - there's no need to measure back from a fixed thread stop or work out where a partial-length rod's thread will run out.\u003c\/p\u003e\n\u003cp\u003eDIN 976 is the modern, tighter-tolerance successor to the older DIN 975 threaded rod standard, and the two designations are commonly quoted together for this type of stud\/studding bar - this rod is manufactured to the current DIN 976 specification. The zinc plating gives good protection against surface rust, making this an economical choice for general construction and fixing work.\u003c\/p\u003e\n\u003cp\u003eBeing fully threaded rather than threaded only at each end, this rod can also be cut to any shorter length on site using a hacksaw or angle grinder and will still take a nut cleanly at any point along the cut length - just deburr the cut end first so a nut runs on without binding.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eKey Features\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eFully threaded along the complete 1000mm (39.4\") length - not just at the ends - so a nut can be fixed anywhere along the rod\u003c\/li\u003e\n\u003cli\u003eManufactured to DIN 976, the current tighter-tolerance standard that succeeded DIN 975, and commonly cross-referenced against both designations\u003c\/li\u003e\n\u003cli\u003eStandard right-hand ISO metric thread, tightening in the usual clockwise direction as a nut is run down the rod\u003c\/li\u003e\n\u003cli\u003eZinc-plated steel finish giving reliable corrosion resistance\u003c\/li\u003e\n\u003cli\u003eSupplied in a full 1000mm (39.4\") length across fourteen thread sizes, from M4 up to M30\u003c\/li\u003e\n\u003cli\u003eCan be cut to shorter lengths on site with a hacksaw or angle grinder without losing thread function at the new end\u003c\/li\u003e\n\u003cli\u003eAn economical choice\u003c\/li\u003e\n\u003cli\u003eBroad size range covers everything from light fixing and cabinet work (M4-M6) through to heavier structural and mounting jobs (M20-M30) in one consistent product line\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eSpecification\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eMaterial: Steel, zinc-plated\u003c\/li\u003e\n\u003cli\u003eStandards: DIN 975 \/ DIN 976\u003c\/li\u003e\n\u003cli\u003eThread: Fully threaded, right-hand, ISO metric\u003c\/li\u003e\n\u003cli\u003eLength: 1000mm (39.4\") - full length, every size\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eFull size range:\u003c\/strong\u003e all fourteen thread sizes below are supplied in the same 1000mm (39.4\") length, so the only variable between them is the thread diameter.\u003c\/p\u003e\n\u003ctable\u003e\n\u003cthead\u003e\n\u003ctr\u003e\n\u003cth\u003eThread Size\u003c\/th\u003e\n\u003cth\u003eNominal Diameter (mm)\u003c\/th\u003e\n\u003cth\u003eNominal Diameter (in)\u003c\/th\u003e\n\u003cth\u003eLength\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003c\/thead\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003ctd\u003eM4\u003c\/td\u003e\n\u003ctd\u003e4mm\u003c\/td\u003e\n\u003ctd\u003e0.157\"\u003c\/td\u003e\n\u003ctd\u003e1000mm (39.4\")\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eM5\u003c\/td\u003e\n\u003ctd\u003e5mm\u003c\/td\u003e\n\u003ctd\u003e0.197\"\u003c\/td\u003e\n\u003ctd\u003e1000mm (39.4\")\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eM6\u003c\/td\u003e\n\u003ctd\u003e6mm\u003c\/td\u003e\n\u003ctd\u003e0.236\"\u003c\/td\u003e\n\u003ctd\u003e1000mm (39.4\")\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eM8\u003c\/td\u003e\n\u003ctd\u003e8mm\u003c\/td\u003e\n\u003ctd\u003e0.315\"\u003c\/td\u003e\n\u003ctd\u003e1000mm (39.4\")\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eM10\u003c\/td\u003e\n\u003ctd\u003e10mm\u003c\/td\u003e\n\u003ctd\u003e0.394\"\u003c\/td\u003e\n\u003ctd\u003e1000mm (39.4\")\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eM12\u003c\/td\u003e\n\u003ctd\u003e12mm\u003c\/td\u003e\n\u003ctd\u003e0.472\"\u003c\/td\u003e\n\u003ctd\u003e1000mm (39.4\")\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eM14\u003c\/td\u003e\n\u003ctd\u003e14mm\u003c\/td\u003e\n\u003ctd\u003e0.551\"\u003c\/td\u003e\n\u003ctd\u003e1000mm (39.4\")\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eM16\u003c\/td\u003e\n\u003ctd\u003e16mm\u003c\/td\u003e\n\u003ctd\u003e0.630\"\u003c\/td\u003e\n\u003ctd\u003e1000mm (39.4\")\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eM18\u003c\/td\u003e\n\u003ctd\u003e18mm\u003c\/td\u003e\n\u003ctd\u003e0.709\"\u003c\/td\u003e\n\u003ctd\u003e1000mm (39.4\")\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eM20\u003c\/td\u003e\n\u003ctd\u003e20mm\u003c\/td\u003e\n\u003ctd\u003e0.787\"\u003c\/td\u003e\n\u003ctd\u003e1000mm (39.4\")\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eM22\u003c\/td\u003e\n\u003ctd\u003e22mm\u003c\/td\u003e\n\u003ctd\u003e0.866\"\u003c\/td\u003e\n\u003ctd\u003e1000mm (39.4\")\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eM24\u003c\/td\u003e\n\u003ctd\u003e24mm\u003c\/td\u003e\n\u003ctd\u003e0.945\"\u003c\/td\u003e\n\u003ctd\u003e1000mm (39.4\")\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eM27\u003c\/td\u003e\n\u003ctd\u003e27mm\u003c\/td\u003e\n\u003ctd\u003e1.063\"\u003c\/td\u003e\n\u003ctd\u003e1000mm (39.4\")\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eM30\u003c\/td\u003e\n\u003ctd\u003e30mm\u003c\/td\u003e\n\u003ctd\u003e1.181\"\u003c\/td\u003e\n\u003ctd\u003e1000mm (39.4\")\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003cp\u003e\u003cstrong\u003eTypical Applications\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eBecause it takes a nut anywhere along its length rather than only at pre-cut ends, this studding bar suits jobs where the exact fixing position isn't known until you're on site:\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eGeneral construction and structural framework - tying, bracing and fixing structural elements together on site\u003c\/li\u003e\n\u003cli\u003eScaffolding assembly - providing a continuous through-thread where fixing points aren't fixed to a set position\u003c\/li\u003e\n\u003cli\u003eMachinery and equipment mounting - anchoring motors, panels and plant equipment where nuts need to be positioned to suit the mounting holes\u003c\/li\u003e\n\u003cli\u003eFurniture and fixture assembly - joining panels and frames where a long, continuous fixing point is required\u003c\/li\u003e\n\u003cli\u003eSuspended ceiling and services hanging - supporting ceiling grids, ductwork and cable trays from an overhead fixing\u003c\/li\u003e\n\u003cli\u003eGeneral DIY and home repair - cut to length on site for shelving, brackets and other ad-hoc fixing jobs around the home\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cstrong\u003eInstallation Guidance\u003c\/strong\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eFully threaded with a standard right-hand ISO metric thread, so a nut can be started and run down from either end of the rod\u003c\/li\u003e\n\u003cli\u003eBecause the thread is continuous rather than stopping at fixed points, a nut can also be positioned and tightened anywhere along the rod's length, not just at the ends\u003c\/li\u003e\n\u003cli\u003eTo shorten on site, cut with a hacksaw or angle grinder - the thread still functions right up to the new cut end\u003c\/li\u003e\n\u003cli\u003eDeburr the cut end with a file before fitting a nut, so it runs on cleanly rather than binding on a damaged first thread\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003eOrder before 2pm Mon–Fri for same-day dispatch from our UK warehouse.\u003c\/p\u003e","brand":"DIYUK","offers":[{"title":"M4 \/ Pack of: 1","offer_id":41351514456198,"sku":"ROD-ZINC-DIN976-M4-01","price":10.22,"currency_code":"GBP","in_stock":false},{"title":"M4 \/ Pack of: 2","offer_id":41351515308166,"sku":"ROD-ZINC-DIN976-M4-02","price":10.6,"currency_code":"GBP","in_stock":false},{"title":"M4 \/ Pack of: 5","offer_id":41351515340934,"sku":"ROD-ZINC-DIN976-M4-05","price":11.72,"currency_code":"GBP","in_stock":false},{"title":"M5 \/ Pack of: 1","offer_id":41351514488966,"sku":"ROD-ZINC-DIN976-M5-01","price":10.47,"currency_code":"GBP","in_stock":false},{"title":"M5 \/ Pack of: 2","offer_id":41351515373702,"sku":"ROD-ZINC-DIN976-M5-02","price":10.97,"currency_code":"GBP","in_stock":false},{"title":"M5 \/ Pack of: 5","offer_id":41351515406470,"sku":"ROD-ZINC-DIN976-M5-05","price":12.47,"currency_code":"GBP","in_stock":false},{"title":"M6 \/ Pack of: 1","offer_id":41351514521734,"sku":"ROD-ZINC-DIN976-M6-01","price":10.47,"currency_code":"GBP","in_stock":false},{"title":"M6 \/ Pack of: 2","offer_id":41351515439238,"sku":"ROD-ZINC-DIN976-M6-02","price":11.1,"currency_code":"GBP","in_stock":false},{"title":"M6 \/ Pack of: 5","offer_id":41351515472006,"sku":"ROD-ZINC-DIN976-M6-05","price":12.72,"currency_code":"GBP","in_stock":false},{"title":"M8 \/ Pack of: 1","offer_id":41351514554502,"sku":"ROD-ZINC-DIN976-M8-01","price":11.1,"currency_code":"GBP","in_stock":false},{"title":"M8 \/ Pack of: 2","offer_id":41351515504774,"sku":"ROD-ZINC-DIN976-M8-02","price":12.22,"currency_code":"GBP","in_stock":false},{"title":"M8 \/ Pack of: 5","offer_id":41351515537542,"sku":"ROD-ZINC-DIN976-M8-05","price":16.73,"currency_code":"GBP","in_stock":false},{"title":"M10 \/ Pack of: 1","offer_id":41351514587270,"sku":"ROD-ZINC-DIN976-M10-01","price":11.72,"currency_code":"GBP","in_stock":false},{"title":"M10 \/ Pack of: 2","offer_id":41351515570310,"sku":"ROD-ZINC-DIN976-M10-02","price":13.47,"currency_code":"GBP","in_stock":false},{"title":"M10 \/ Pack of: 5","offer_id":41351515603078,"sku":"ROD-ZINC-DIN976-M10-05","price":19.85,"currency_code":"GBP","in_stock":false},{"title":"M12 \/ Pack of: 1","offer_id":41351514620038,"sku":"ROD-ZINC-DIN976-M12-01","price":12.47,"currency_code":"GBP","in_stock":false},{"title":"M12 \/ Pack of: 2","offer_id":41351515635846,"sku":"ROD-ZINC-DIN976-M12-02","price":16.1,"currency_code":"GBP","in_stock":false},{"title":"M12 \/ Pack of: 5","offer_id":41351515668614,"sku":"ROD-ZINC-DIN976-M12-05","price":23.72,"currency_code":"GBP","in_stock":false},{"title":"M14 \/ Pack of: 1","offer_id":41351514652806,"sku":"ROD-ZINC-DIN976-M14-01","price":13.6,"currency_code":"GBP","in_stock":false},{"title":"M14 \/ Pack of: 2","offer_id":41351515701382,"sku":"ROD-ZINC-DIN976-M14-02","price":18.35,"currency_code":"GBP","in_stock":false},{"title":"M14 \/ Pack of: 5","offer_id":41351515734150,"sku":"ROD-ZINC-DIN976-M14-05","price":29.47,"currency_code":"GBP","in_stock":false},{"title":"M16 \/ Pack of: 1","offer_id":41351514685574,"sku":"ROD-ZINC-DIN976-M16-01","price":15.97,"currency_code":"GBP","in_stock":false},{"title":"M16 \/ Pack of: 2","offer_id":41351515766918,"sku":"ROD-ZINC-DIN976-M16-02","price":20.97,"currency_code":"GBP","in_stock":false},{"title":"M16 \/ Pack of: 5","offer_id":41351515799686,"sku":"ROD-ZINC-DIN976-M16-05","price":35.97,"currency_code":"GBP","in_stock":false},{"title":"M18 \/ Pack of: 1","offer_id":41351514718342,"sku":"ROD-ZINC-DIN976-M18-01","price":17.47,"currency_code":"GBP","in_stock":false},{"title":"M18 \/ Pack of: 2","offer_id":41351515832454,"sku":"ROD-ZINC-DIN976-M18-02","price":23.72,"currency_code":"GBP","in_stock":false},{"title":"M18 \/ Pack of: 5","offer_id":41351515865222,"sku":"ROD-ZINC-DIN976-M18-05","price":43.22,"currency_code":"GBP","in_stock":false},{"title":"M20 \/ Pack of: 1","offer_id":41351514751110,"sku":"ROD-ZINC-DIN976-M20-01","price":19.23,"currency_code":"GBP","in_stock":false},{"title":"M20 \/ Pack of: 2","offer_id":41351515897990,"sku":"ROD-ZINC-DIN976-M20-02","price":27.35,"currency_code":"GBP","in_stock":false},{"title":"M20 \/ Pack of: 5","offer_id":41351515930758,"sku":"ROD-ZINC-DIN976-M20-05","price":51.97,"currency_code":"GBP","in_stock":false},{"title":"M22 \/ Pack of: 1","offer_id":41351514783878,"sku":"ROD-ZINC-DIN976-M22-01","price":18.72,"currency_code":"GBP","in_stock":false},{"title":"M22 \/ Pack of: 2","offer_id":41351515963526,"sku":"ROD-ZINC-DIN976-M22-02","price":26.6,"currency_code":"GBP","in_stock":false},{"title":"M22 \/ Pack of: 5","offer_id":41351515996294,"sku":"ROD-ZINC-DIN976-M22-05","price":50.22,"currency_code":"GBP","in_stock":false},{"title":"M24 \/ Pack of: 1","offer_id":41351514816646,"sku":"ROD-ZINC-DIN976-M24-01","price":22.85,"currency_code":"GBP","in_stock":false},{"title":"M24 \/ Pack of: 2","offer_id":41351516029062,"sku":"ROD-ZINC-DIN976-M24-02","price":34.85,"currency_code":"GBP","in_stock":false},{"title":"M24 \/ Pack of: 5","offer_id":41351516061830,"sku":"ROD-ZINC-DIN976-M24-05","price":70.85,"currency_code":"GBP","in_stock":false},{"title":"M27 \/ Pack of: 1","offer_id":41351514849414,"sku":"ROD-ZINC-DIN976-M27-01","price":21.97,"currency_code":"GBP","in_stock":false},{"title":"M27 \/ Pack of: 2","offer_id":41351516094598,"sku":"ROD-ZINC-DIN976-M27-02","price":32.97,"currency_code":"GBP","in_stock":false},{"title":"M27 \/ Pack of: 5","offer_id":41351516127366,"sku":"ROD-ZINC-DIN976-M27-05","price":73.72,"currency_code":"GBP","in_stock":false},{"title":"M30 \/ Pack of: 1","offer_id":41351514882182,"sku":"ROD-ZINC-DIN976-M30-01","price":31.47,"currency_code":"GBP","in_stock":false},{"title":"M30 \/ Pack of: 2","offer_id":41351516160134,"sku":"ROD-ZINC-DIN976-M30-02","price":51.97,"currency_code":"GBP","in_stock":false},{"title":"M30 \/ Pack of: 5","offer_id":41351516192902,"sku":"ROD-ZINC-DIN976-M30-05","price":121.22,"currency_code":"GBP","in_stock":false}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0549\/0245\/6454\/files\/rzmainb.png?v=1726491248"}],"url":"https:\/\/diyuk.co\/collections\/threaded-rod.oembed","provider":"DIYUK LTD","version":"1.0","type":"link"}